Адаптация на 1B (Active steering) на Audi RS4 2012
Публикувано на: Пон Мар 09, 2015 12:59 pm
Колеги, имам едно RS4 за правене. Колата е била блъсната и са сменили рейката, като майстора ми се кълне, че са сменили само механиката, но в лог-а на VCDS има и друго:
Address 1B: Active Steering (J792) Labels: None
Part No SW: 8K0 907 144 J HW: 8K0 907 144 J
Component: DYNAMIKLENK. H06 0690
Revision: 52001005 Serial number: --------------
Coding: 030000
Shop #: WSC 06325 000 00000
VCID: 36693801815C5C9
1 Fault Found:
01087 - Basic Setting Not Performed
000 - - - MIL ON
Freeze Frame:
Fault Status: 11100000
Fault Priority: 2
Fault Frequency: 1
Time Indication: 0
Freeze Frame:
Count: 56
Count: 1
Hex Value: 0x0085
Hex Value: 0x851A
Hex Value: 0x0C00
Hex Value: 0x0000
Address 44: Steering Assist Labels: None
Control Module Part Number: 8K0 909 144 F HW: 8K0 909 144 B
Component and/or Version: RCEPS H36 0507
Software Coding: 100000010001
Work Shop Code: WSC 06325 000 00000
ASAM Dataset: EV_RCEPSAU48X 008014 (AU48)
VCID: 346D02099F204E9
Fault Codes have been Erased
2 Faults Found:
5258753 - Steering End Stops Not Learned
C10AC F0 [137] - Unknown Error Elaboration
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 192
Mileage: 40890 km
Date: 2015.03.06
Time: 15:40:52
4215041 - Control Module
C109F 00 [137] - Incorrect Version Installed
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 192
Mileage: 40890 km
Date: 2015.03.06
Time: 15:40:52
Не съм много близък с аудитата...
В ростех пишат:
Security Access
40168 = Basic Setting Enabling
Basic Setting
Steering Angle Sensor (G85) Calibration
[Select]
[16 - Steering Wheel]
Turn steering wheel at least 30 ° left or right and back straight ahead (Tolerance: ±5.0 °).
[Security Access - 16]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
[Meas. Blocks - 08]
Group 033 Field 3 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±1.5 °
[Done, Go Back]
After the Steering Angle Sensor (G85) Calibration is completed, the 44-Steering Assist (J500) module may have DTC C10AC - Steering End Stops Not Learned stored. The steering limit end stops need to be adapted as follows:
Start the engine and turn the steering to full right lock and hold it for 5 to 10 seconds. The vehicle should produce an audible beep
Turn the steering to the complete left lock and the same audible beep should sound.
Straighten the wheels and wait 5 to 10 seconds while observing the steering and traction control warnings. They should extinguish although it is advised to scan the vehicle again for DTCs prior to the test drive.
Notes:
To confirm the status of the G85 calibration see MVB group 032.
If the basic setting group results in an error message verify the live G85 reading is ±1.5 °. Readings such as 359° would indicate the slip ring is mechanically out one full turn.
The slip ring is the 16-Steering Wheel Electronics module. If the vehicle deployed Airbag(s) and the slip ring was replaced make sure the module is long coded using VCDS.
Some Audi 8K/8T models may have address 1B-Active Steering (J792) installed in addition to 16-Steering Wheel electronics. If mechanical repairs are made to the front end or front end alignment those vehicles may require additional Basic Settings steps to resolve DTC: 01087 - Basic Setting Not Performed. Registered users can contact us directly with the complete Auto Scan, VIN number and summary of mechanical repairs for additional assistance.
Някой знае ли процедурата?
Address 1B: Active Steering (J792) Labels: None
Part No SW: 8K0 907 144 J HW: 8K0 907 144 J
Component: DYNAMIKLENK. H06 0690
Revision: 52001005 Serial number: --------------
Coding: 030000
Shop #: WSC 06325 000 00000
VCID: 36693801815C5C9
1 Fault Found:
01087 - Basic Setting Not Performed
000 - - - MIL ON
Freeze Frame:
Fault Status: 11100000
Fault Priority: 2
Fault Frequency: 1
Time Indication: 0
Freeze Frame:
Count: 56
Count: 1
Hex Value: 0x0085
Hex Value: 0x851A
Hex Value: 0x0C00
Hex Value: 0x0000
Address 44: Steering Assist Labels: None
Control Module Part Number: 8K0 909 144 F HW: 8K0 909 144 B
Component and/or Version: RCEPS H36 0507
Software Coding: 100000010001
Work Shop Code: WSC 06325 000 00000
ASAM Dataset: EV_RCEPSAU48X 008014 (AU48)
VCID: 346D02099F204E9
Fault Codes have been Erased
2 Faults Found:
5258753 - Steering End Stops Not Learned
C10AC F0 [137] - Unknown Error Elaboration
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 192
Mileage: 40890 km
Date: 2015.03.06
Time: 15:40:52
4215041 - Control Module
C109F 00 [137] - Incorrect Version Installed
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 192
Mileage: 40890 km
Date: 2015.03.06
Time: 15:40:52
Не съм много близък с аудитата...
В ростех пишат:
Security Access
40168 = Basic Setting Enabling
Basic Setting
Steering Angle Sensor (G85) Calibration
[Select]
[16 - Steering Wheel]
Turn steering wheel at least 30 ° left or right and back straight ahead (Tolerance: ±5.0 °).
[Security Access - 16]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
[Meas. Blocks - 08]
Group 033 Field 3 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±1.5 °
[Done, Go Back]
After the Steering Angle Sensor (G85) Calibration is completed, the 44-Steering Assist (J500) module may have DTC C10AC - Steering End Stops Not Learned stored. The steering limit end stops need to be adapted as follows:
Start the engine and turn the steering to full right lock and hold it for 5 to 10 seconds. The vehicle should produce an audible beep
Turn the steering to the complete left lock and the same audible beep should sound.
Straighten the wheels and wait 5 to 10 seconds while observing the steering and traction control warnings. They should extinguish although it is advised to scan the vehicle again for DTCs prior to the test drive.
Notes:
To confirm the status of the G85 calibration see MVB group 032.
If the basic setting group results in an error message verify the live G85 reading is ±1.5 °. Readings such as 359° would indicate the slip ring is mechanically out one full turn.
The slip ring is the 16-Steering Wheel Electronics module. If the vehicle deployed Airbag(s) and the slip ring was replaced make sure the module is long coded using VCDS.
Some Audi 8K/8T models may have address 1B-Active Steering (J792) installed in addition to 16-Steering Wheel electronics. If mechanical repairs are made to the front end or front end alignment those vehicles may require additional Basic Settings steps to resolve DTC: 01087 - Basic Setting Not Performed. Registered users can contact us directly with the complete Auto Scan, VIN number and summary of mechanical repairs for additional assistance.
Някой знае ли процедурата?